Saint Wien Enterprise Inc., Ltd

IR100- Series Multi functions IR Remote Control Timer Enjoy your Light Save Energy with IR Remote Control... Multi functions IR Remote Control Timer includes IR Controller & IR Receiver/lamp holder. The design provides original switch direct ON OFF or use IR Controller remote control. In sight of distance remote control IR Receiver in anywhere. ONE KEY remote control is easy and simple for old man, children, the handicapped & tired person. Simulate the activity of family with ON OFF cycling of light while no body is home to prevent theft. Any one IR controller may control any one IR receiver ● FUNCTIONS of IR controller and IR Receiver/lamp holder 1. Power ON: Original SW direct ON OFF receiver/lamp holder without IR Controller. Power ON has ON Continuous or ON T1. Please see “Power ON Mode selection” 2. [ALLON] or [ALLOFF]: Direct control ON or OFF all ID Nos. of receiver/lamp holders. 3. [1ONOFF]~[8ONOFF]: Direct ON OFF control correspond ID Nos. See “ID Nos. selection” IR100-R1, IR101-R1 have ID Nos.1~8. IR101-R3 has 3 relays ID Nos.1~3. 4. [T1]: ON T1 time then OFF automatically for correspond ID Nos. 5. [T1T2]: ON T1 then OFF T2. Repeat ON OFF cycle automatically for correspond ID Nos. 6. [-T1]: OFF T1 time then ON continuous automatically for correspond ID Nos. ● LED indicator on IR Receiver/lamp holder 1. Indicating city power & operation status * LED Steady ON: IR Receiver/lamp holder is off and standby now. * LED Flash one shoot: IR Receiver/lamp holder responses each keying of IR Controller * LED Flash at 5 different rates: IR Receiver/lamp holder is ON and timing now for different time unit. Flash rate shown (1)0.5s is on 1S (2)1.5S is on 10S (3)2.5S is on 1M (4)3.5S is on 10M (5)4.5S is on continuous without timing 2. LED Flash at different rate show the device is ON. If receiver/lamp is not active it shows the lamp may be burn-out. 3. LED shows the location of receiver/lamp holder. ● PROGram T1 T2 Note: Keying over 10S is invalid while set time interval & unit of T1 T2. Key symbol: [xx] 1. Individual ID Nos. time range is (Time interval 0~99) x (Time unit 1S 10S 1M or 10M) = 1S~990M 2. [T1] or [T2] interval: Key [PROG] then Key [0~99] final Key [T1] or [T2] 3. [T1] & [T2] unit: Key [PROG] then Key [1S or 10S 1M 10M] Note: T1 T2 works on same unit ● Power ON Mode selection Be care of wires (Jumper on is ON T1) A. IR100- 1. Unscrew holding screw inside E27 lamp holder. 2. Open housing by turning counter-clock and access to PCB. 3. Check PCB. Jumper on is “ON T1”, no jumper is “ON Continuous” B. IR101- Unscrews & Check PCB. Jumper on is “ON T1”, no jumper is “ON Continuous” ● ID Nos selection Set DIP SW for correspond ID Nos. of IR100-R1 IR101-R1 Check PCB inside receiver as “Power ON Mode selection” Set DIP SW as shown below DIP SW ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 No. 1 OFF OFF OFF OFF ON ON ON ON No. 2 OFF OFF ON ON OFF OFF ON ON No, 3 OFF ON OFF ON OFF ON OFF ON DIP SW N0.1 2 3 OFF is ID 1 DIP SW N0.1 2 3 ON is ID 8 ● SPECIFICATIONS of IR Receiver/Lamp Holder 1. Power Source & Consumption: White & black 85~265VAC 50/60Hz standby 0.3W & relays on 3W. Fuse 5A 2. Load capacity: IR100-R1, IR101-R1: 300W for E27 110/220V 50/60Hz IR101-R3: 3A for single relay with wires 20cm, color code for 3 loads ID 1=black, brown; ID 2=black, red; ID 3=black, orange. 3 relays’ total load never over 5A 110/220V 50/60Hz 3. Time range & Accuracy: 1~99S, 990S, 99M, 999M +-0.1% +-1S 4. Dimensions: IR100- Dia.58mm L110mm ; IR101- Dia.113mm H58mm 5. Ambient conditions: 50℃ 85%RH Max ● SPECIFICATIONS of IR Controller IR100-T1 Dimension: L133mm W51mm H21mm 1. Battery: AAA(1.5V) x 2 2. Control distance: 10M in sight distance Warning: (1) Power off before opening IR Receiver/lamp holder (2) Do not use on dimming circuits (3) For indoor use only.